HB商城

环保商城 电动压差旁通阀/电动压差旁通阀型号

电动压差旁通阀/电动压差旁通阀型号

  • 产地
  • 所在地
  • 中国
  • 上海上海市

更新时间:2014-11-19

有效日期:已过期

产品详情

丹富斯电动旁通压差控制阀(旁通压差阀)不需任何外来动力,依靠管网自身的压力工作,保持阀门两端的压差相对恒定,广泛用于*空调集分水器之间,热力泵供回水之间。可有效保持设备不被损坏。可以代替电动旁通压差阀。  
性能及特点 电动压差旁通阀/电动压差旁通阀型号 
1.恒定阀门两端及被控系统压差支持用户系统变流量运行;  
2.依靠压差自动工作无须外界动力;  
3.可以直接显示控制压差;  
4.可以直接设定控制压差;  
5.控制压差调节灵敏,操作简单;  
6.介质温度:0-150℃;  
7.控制压差可调范围:0.05-0.6MPa;  
8.控制压差误差≤±5%。  
选型  
可根据管道等径选用,用于旁通安装时可缩径使用。  
丹富斯电动压差旁通阀用途: 电动压差旁通阀/电动压差旁通阀型号 
1.常闭型旁通压差控制阀用于燃油、燃气热源供、回水管,*空调的分、集水器之间,作为一次测定流量,二次侧变流量系统的旁通安装,可有效保护燃油、燃气机组不会因流量过小导致的温度过高而损坏,也可有效的保护冷水机组因流量过小而造成的局部冻结而损坏。  
2.常开型旁通压差控制阀用于高度差较大且热源在高区的集中供热系统,使用时按高度差设定该阀的压差,并在低区回水管适当位置安装减压泵、止回阀,调节阀组成的回水减压装置,通过调节阀来调节并设定回水管压力,这样既可保护高区用户不会出现倒空现象,又可保护低区设备不会因压力过高而损坏。  

电动压差旁通阀控制的作用:

    本系统适用于*空调的冷冻水/热水系统的压差旁通控制用途。
    压差旁通的作用主要在于,维持冷冻水/热水系统能够在末端负荷较低的情况下,保证冷冻机/热交换器等设备的正常运转。

产品特点:

  ★执行器选用铸铝支架及塑料外壳,体积小、重量轻

  ★选用永磁同步电机,并带有磁滞离合机构,具有可靠的自我保护功能

  ★-适合多种控制信号:增量(浮点)、电压(0~10V)、电流(4~20mA)

  ★-具有0~10V或4~20mA反馈信号(选配)

  ★传动齿轮采用金属齿轮,大大提高了驱动器的使用寿命

  ★功耗低、输出力大、噪音小

工作原理:  压差控制器DPC-1通过检测供/回水主管的压力差,与设定值相比较,通过控制电动两通阀的开度,使供水与回水间实现旁通,以保持所需的压力差值。
压力差增大时,红触点与黄触点接通,压力减少时,红触点与蓝触点接通,红触点可以停留在中间位置,与其他触点没有电气连接。

Dan fuss electric bypass pressure difference control valve (pressure differential bypass valve) does not need any external power, relying on the network's own work pressure, differential pressure at the ends of the valve is relatively constant, is widely used in central air conditioning set between water segregator, heat pump for water. Can effectively keep the equipment is not damaged. Can replace electric bypass pressure differential valve.

Performance and characteristics of the

1. Constant on both ends of the valve and controlled system differential pressure support user system variable flow operation;

2. On differential pressure automatic work without external power;

3. Can directly display control pressure difference;

4. Can be directly set control pressure difference;

5. Controlling differential pressure regulating sensitivity, simple operation;

6. The medium temperature: 0-150 ℃;

7. General control pressure adjustable range: 0.05 to 0.6 MPa;

8. Control the differential error of plus or minus 5% or less.

The selection

According to pipe diameter selection, installation can be used to bypass reducing use.

USES:

1. Normally closed type by-pass differential pressure control valve is used for fuel, gas, heat supply and return pipe, central air conditioning, between points, Siamese as a measuring flow, secondary side bypass installation of variable flow system, which can effectively protect the fuel, gas units will not damage due to flow high temperature caused by too small, also is effective in protecting the chiller caused by traffic is too small and partial freezing damage.

2. Normally open type by-pass pressure difference control valve used in height difference is bigger and the heat source in the central heating system of high area, when used according to the difference in height setting of the valve pressure difference, and in the low return pipe position vacuum pump installation, check valve, regulating valve of backwater pressure-relief devices, through the control valve to regulate and set back to the pipe pressure, so that can protect high area users won't appear empty phenomenon, but also protect the equipment will not damaged by high pressure low area.

The role of electric differential pressure bypass valve control:

This system is the central air conditioning chilled water/hot water system of differential pressure bypass control purposes.

The effect of differential pressure bypass key lies in the fact that chilled water/hot water system can under the lower end of the load, ensure the refrigerator/heat exchanger and the normal operation.

Product features:

Taken the actuator selection aluminum bracket and plastic shell, small volume, light weight

U choose permanent magnet synchronous motor, with magnetic hysteresis clutch mechanism, has reliable self-protection function

U - suitable for a variety of control signal: increment (float), voltage (0 ~ 10 v), current (4 ~ 20 ma)

U - with 0 ~ 10 v or 4 ~ 20 ma feedback signal (optional)

U use a metal gear transmission gear, greatly improve the service life of the drive

U low power consumption, big output power, low noise

Working principle: by testing for differential pressure controller DPC - 1 / water head pressure difference, compared with the set value, by controlling the electric two-way valve opening, make to by-pass between water supply and return water, in order to maintain the required pressure difference.

Differential pressure increases, the red contact, connected with yellow contact pressure to reduce, the red contact with blue contacts connected, red contact can stay in the middle position, and other contact no electrical connections.

 


免责声明:以上所展示的信息由企业自行提供,内容的真实性、准确性和合法性由发布企业负责,环保在线对此不承担任何保证责任。

发布询价单

丹富斯国际贸易(上海)有限

型:
生产厂家
联系人:
采购部

联系我时,请说明是在环保在线上看到的,谢谢

商家概况

主营产品:
平衡阀|静态平衡阀|压差平衡阀|电动二通阀|水力控制阀|
公司性质:
生产厂家

该商家其它产品

涡轮蝶阀,涡轮手柄蝶阀-丹富斯阀门集团

涡轮蝶阀,涡轮手...

摘要:丹富斯阀门厂专业生产蝶阀 [详细]
法兰连接Y型过滤器

法兰连接Y型过滤...

摘要:丹富斯阀门厂专业生产阀门 [详细]
Y型过滤器,进口过滤器-丹富斯阀门集团

Y型过滤器,进口...

摘要:Y型过滤器专业生产销售厂家 [详细]
法兰全焊接球阀,法兰全焊球阀厂家

法兰全焊接球阀,...

摘要:丹富斯法兰全焊接球阀表面 [详细]
涡轮全焊接球阀,涡轮全焊接球阀原理

涡轮全焊接球阀,...

摘要:丹富斯涡轮全焊接球阀表面 [详细]
丹富斯自力式压差控制阀性能特点、

丹富斯自力式压差...

摘要:丹富斯自力式压差控制阀, [详细]
丹富斯电动V型调节球阀价格,零泄漏电动调节阀、

丹富斯电动V型调...

摘要:丹富斯ZDRV型电子式电动V型 [详细]
全焊接球阀原理/丹富斯全焊接球阀厂家

全焊接球阀原理/...

摘要:一体式焊接球阀吸取*进技术 [详细]

提示

×

*您想获取产品的资料:

以上可多选,勾选其他,可自行输入要求

个人信息:

关闭